Reading/Writing Disk Sectors (Absolute Disk Read/Write)

Windows 9x

Windows 9x provides a vxd called vwin32.vxd using which msdos functions including absolute disk read/write can be performed. A handle to vwin32.vxd must be first created using the CreateFile function. After creating the handle DeviceIoControl function must be used with the correct control code to read or write from the disk drives. The control code depends on the type of the function you want to perform.

The control codes for vwin32.vxd are ...

The lpvInBuffer & lpvOutBuffer params of DeviceIoControl function must point to addresses of DIOC_REGISTERS strUCtures . This structure contains the state of the processor registers before ioctl and after ioctl.

Windows NT/2K/XP

In Windows NT/2K/XP the CreateFile function can be used to open a disk drive or a partition on it. After getting a handle to the disk drive using CreateFile function the ReadFile function can be used to read sectors and the WriteFile function can be used to write to the drive.If you want to open a logical drive give the filename param of the CreateFile function as "\\\\.\\a:" or "\\\\.\\c:" ... etc. and if you want to open a physical drive for raw reading/writing give the filename param as "\\\\.\\PhysicalDrive0" or "\\\\.\\PhysicalDrive1" ... etc

Code to read disk sectors from win 9x/NT/2K/XP

Reads [numberofsectors] disk sectors from [drive {0=A, 1=B, 2=C, ...}] drive starting from [startinglogicalsector]

To read sectors from win 9x int 21h's 7305h extention is used (Extended Absolute Disk Read/Write). For more info about int 21h's 7305h extention refer Ralf Brown's interrupt list.

Word>char * ReadSectors(int drive, DWORD startinglogicalsector, int numberofsectors){// All msdos data structures must be packed on a 1 byte boundary#pragma pack (1)struct{DWORD StartingSector ;WORD NumberOfSectors ;DWORD pBuffer;}ControlBlock;#pragma pack ()#pragma pack (1)typedef struct _DIOC_REGISTERS{ DWORD reg_EBX; DWORD reg_EDX; DWORD reg_ECX; DWORD reg_EAX; DWORD reg_EDI; DWORD reg_ESI; DWORD reg_Flags;} DIOC_REGISTERS ;#pragma pack ()char* buffer = (char*)malloc (512*numberofsectors);HANDLE hDevice ;DIOC_REGISTERS reg ;BOOLfResult ;DWORD cb ;// Creating handle to vwin32.vxd (win 9x)hDevice = CreateFile ( "\\\\.\\vwin32", 0, 0, NULL, 0, FILE_FLAG_DELETE_ON_CLOSE, NULL );if ( hDevice == INVALID_HANDLE_VALUE ){// win NT/2K/XP code HANDLE hDevice;DWORD bytesread;char _devicename[] = "\\\\.\\A:";_devicename[4] += drive;// Creating a handle to disk drive using CreateFile () function ..hDevice = CreateFile(_devicename, GENERIC_READ, FILE_SHARE_READ  FILE_SHARE_WRITE, NULL, OPEN_EXISTING, 0, NULL);if (hDevice == INVALID_HANDLE_VALUE)return NULL;// Setting the pointer to point to the start of the sector we want to read ..SetFilePointer (hDevice, (startinglogicalsector*512), NULL, FILE_BEGIN);if (!ReadFile (hDevice, buffer, 512*numberofsectors, &bytesread, NULL) )return NULL;}else{// code for win 95/98ControlBlock.StartingSector = (DWORD)startinglogicalsector;ControlBlock.NumberOfSectors = (DWORD)numberofsectors ;ControlBlock.pBuffer = (DWORD)buffer ;//-----------------------------------------------------------// SI contains read/write mode flags// SI=0h for read and SI=1h for write// CX must be equal to ffffh for// int 21h's 7305h extention// DS:BX -> base addr of the// control block structure// DL must contain the drive number// (01h=A:, 02h=B: etc)//-----------------------------------------------------------reg.reg_ESI = 0x00 ;reg.reg_ECX = -1 ;reg.reg_EBX = (DWORD)(&ControlBlock);reg.reg_EDX = drive+1;reg.reg_EAX = 0x7305 ;//6 == VWIN32_DIOC_DOS_DRIVEINFOfResult = DeviceIoControl ( hDevice,6, &(reg), sizeof (reg), &(reg), sizeof (reg), &cb,0);if (!fResult  (reg.reg_Flags & 0x0001)) return NULL; }CloseHandle(hDevice); return buffer;}